Tier 1-3 Standards. The first federal standards (Tier 1) for new nonroad (or off-road) diesel engines were adopted in 1994 for engines over 37 kW (50 hp), to be phased-in from 1996 to 2000. In 1996, a Statement of Principles (SOP) pertaining to nonroad diesel engines was signed between EPA, California ARB and engine makers (including Caterpillar, Cummins, Deere, Detroit Diesel, Deutz, Isuzu, Komatsu, Kubota, Mitsubishi, Navistar, New Holland, Wis-Con, and Yanmar). On August 27, 1998, the EPA signed the final rule reflecting the provisions of the SOP . The 1998 regulation introduced Tier 1 standards for equipment under 37 kW (50 hp) and increasingly more stringent Tier 2 and Tier 3 standards for all equipment with phase-in schedules from 2000 to 2008. The Tier 1-3 standards are met through advanced engine design, with no or only limited use of exhaust gas aftertreatment (oxidation catalysts). Tier 3 standards for NOx+HC are similar in stringency to the 2004 standards for highway engines, however Tier 3 standards for PM were never adopted.
Nonroad Diesel Fuel. At the Tier 1-3 stage, the sulfur content in nonroad diesel fuels was not limited by environmental regulations. The oil industry specification was 0.5% (wt., max), with the average in-use sulfur level of about 0.3% = 3,000 ppm. To enable sulfur-sensitive control technologies in Tier 4 engines—such as catalytic particulate filters and NOx adsorbers—the EPA mandated reductions in sulfur content in nonroad diesel fuels, as follows:
- 500 ppm effective June 2007 for nonroad, locomotive and marine (NRLM) diesel fuels
- 15 ppm (ultra-low sulfur diesel) effective June 2010 for nonroad fuel, and June 2012 for locomotive and marine fuels
California. In most cases, federal nonroad regulations also apply in California, whose authority to set emission standards for new nonroad engines is limited. The federal Clean Air Act Amendments of 1990 (CAA) preempt California’s authority to control emissions from new farm and construction equipment under 175 hp [CAA Section 209(e)(1)(A)] and require California to receive authorization from the federal EPA for controls over other off-road sources [CAA Section 209 (e)(2)(A)].
The US nonroad emission standards are harmonized to a certain degree with European nonroad emission standards.
EPA emission standards for nonroad diesel engines are published in the US Code of Federal Regulations, Title 40, Part 89. Regulatory text, fact sheets and related documents are available from the EPA web site.
Applicability
The nonroad standards cover mobile nonroad diesel engines of all sizes used in a wide range of construction, agricultural and industrial equipment. The EPA definition of the nonroad engine is based on the principle of mobility/portability, and includes engines installed on (1) self-propelled equipment, (2) on equipment that is propelled while performing its function, or (3) on equipment that is portable or transportable, as indicated by the presence of wheels, skids, carrying handles, dolly, trailer, or platform [40 CFR 1068.30]. In other words, nonroad engines are all internal combustion engines except motor vehicle (highway) engines, stationary engines (or engines that remain at one location for more than 12 months), engines used solely for competition, or engines used in aircraft.
Effective May 14, 2003, the definition of nonroad engines was changed to also include all diesel powered engines—including stationary ones—used in agricultural operations in California. This change applies only to engines sold in the state of California; stationary engines sold in other states are not classified as nonroad engines.
The nonroad diesel emission regulations are not applicable to all nonroad diesel engines. Exempted are the following nonroad engine categories:
- Engines used in railway locomotives; those are subject to separate EPA regulations.
- Engines used in marine vessels, also covered by separate EPA regulations. Marine engines below 37 kW (50 hp) are subject to Tier 1-2—but not Tier 4—nonroad standards. Certain marine engines that are exempted from marine standards may be subject to nonroad regulations.
- Engines used in underground mining equipment. Diesel emissions and air quality in mines are regulated by the Mine Safety and Health Administration (MSHA).
- Hobby engines (below 50 cm3 per cylinder)
Examples of regulated applications include farm tractors, excavators, bulldozers, wheel loaders, backhoe loaders, road graders, diesel lawn tractors, logging equipment, portable generators, skid steer loaders, or forklifts.
A new definition of a compression-ignition (diesel) engine was introduced in the 1998 rule, consistent with definitions established for highway engines. The definition focuses on the engine cycle, rather than the ignition mechanism, with the presence of a throttle as an indicator to distinguish between diesel-cycle and otto-cycle operation. Regulating power by controlling the fuel supply in lieu of a throttle corresponds with lean combustion and diesel-cycle operation. This language allows the possibility that a natural gas-fueled engine equipped with a spark plug is considered a compression-ignition engine.
Tier 1-3 Emission Standards
The 1998 nonroad engine regulations were structured as a 3-tiered progression. Each tier involved a phase-in (by horsepower rating) over several years. Tier 1 standards were phased-in from 1996 to 2000. The more stringent Tier 2 standards took effect from 2001 to 2006, and yet more stringent Tier 3 standards phased-in from 2006 to 2008 (Tier 3 standards applied only for engines from 37-560 kW).
Tier 1-3 emissions standards are listed in Table 1. Nonroad regulations use the metric system of units, with regulatory limits expressed in grams of pollutant per kWh.
Table 1
EPA Tier 1-3 nonroad diesel engine emission standards, g/kWh (g/bhp·hr)
| Engine Power | Tier | Year | CO | HC | NMHC+NOx | NOx | PM |
| kW < 8 (hp < 11) | Tier 1 | 2000 | 8.0 (6.0) | – | 10.5 (7.8) | – | 1.0 (0.75) |
| Tier 2 | 2005 | 8.0 (6.0) | – | 7.5 (5.6) | – | 0.8 (0.6) | |
| 8 ≤ kW < 19 (11 ≤ hp < 25) | Tier 1 | 2000 | 6.6 (4.9) | – | 9.5 (7.1) | – | 0.8 (0.6) |
| Tier 2 | 2005 | 6.6 (4.9) | – | 7.5 (5.6) | – | 0.8 (0.6) | |
| 19≤ kW < 37 (25 ≤ hp < 50) | Tier 1 | 1999 | 5.5 (4.1) | – | 9.5 (7.1) | – | 0.8 (0.6) |
| Tier 2 | 2004 | 5.5 (4.1) | – | 7.5 (5.6) | – | 0.6 (0.45) | |
| 37 ≤ kW < 75 (50 ≤ hp < 100) | Tier 1 | 1998 | – | – | – | 9.2 (6.9) | – |
| Tier 2 | 2004 | 5.0 (3.7) | – | 7.5 (5.6) | – | 0.4 (0.3) | |
| Tier 3 | 2008 | 5.0 (3.7) | – | 4.7 (3.5) | – | -† | |
| 75 ≤ kW < 130 (100 ≤ hp < 175) | Tier 1 | 1997 | – | – | – | 9.2 (6.9) | – |
| Tier 2 | 2003 | 5.0 (3.7) | – | 6.6 (4.9) | – | 0.3 (0.22) | |
| Tier 3 | 2007 | 5.0 (3.7) | – | 4.0 (3.0) | – | -† | |
| 130 ≤ kW < 225 (175 ≤ hp < 300) | Tier 1 | 1996 | 11.4 (8.5) | 1.3 (1.0) | – | 9.2 (6.9) | 0.54 (0.4) |
| Tier 2 | 2003 | 3.5 (2.6) | – | 6.6 (4.9) | – | 0.2 (0.15) | |
| Tier 3 | 2006 | 3.5 (2.6) | – | 4.0 (3.0) | – | -† | |
| 225 ≤ kW < 450 (300 ≤ hp < 600) | Tier 1 | 1996 | 11.4 (8.5) | 1.3 (1.0) | – | 9.2 (6.9) | 0.54 (0.4) |
| Tier 2 | 2001 | 3.5 (2.6) | – | 6.4 (4.8) | – | 0.2 (0.15) | |
| Tier 3 | 2006 | 3.5 (2.6) | – | 4.0 (3.0) | – | -† | |
| 450 ≤ kW < 560 (600 ≤ hp < 750) | Tier 1 | 1996 | 11.4 (8.5) | 1.3 (1.0) | – | 9.2 (6.9) | 0.54 (0.4) |
| Tier 2 | 2002 | 3.5 (2.6) | – | 6.4 (4.8) | – | 0.2 (0.15) | |
| Tier 3 | 2006 | 3.5 (2.6) | – | 4.0 (3.0) | – | -† | |
| kW ≥ 560 (hp ≥ 750) | Tier 1 | 2000 | 11.4 (8.5) | 1.3 (1.0) | – | 9.2 (6.9) | 0.54 (0.4) |
| Tier 2 | 2006 | 3.5 (2.6) | – | 6.4 (4.8) | – | 0.2 (0.15) | |
| † Not adopted, engines must meet Tier 2 PM standard. |
Manufacturers who signed the 1998 Consent Decrees with the EPA may have been required to meet the Tier 3 standards one year ahead of schedule (i.e. beginning in 2005).
Voluntary, more stringent emission standards that manufacturers could use to earn a designation of “Blue Sky Series” engines (applicable to Tier 1-3 certifications) are listed in Table 2.
Table 2
EPA voluntary emission standards for nonroad diesel engines, g/kWh (g/bhp·hr)
| Rated Power (kW) | NMHC+NOx | PM |
| kW < 8 | 4.6 (3.4) | 0.48 (0.36) |
| 8 ≤ kW <19 | 4.5 (3.4) | 0.48 (0.36) |
| 19 ≤ kW <37 | 4.5 (3.4) | 0.36 (0.27) |
| 37 ≤ kW < 75 | 4.7 (3.5) | 0.24 (0.18) |
| 75 ≤ kW <130 | 4.0 (3.0) | 0.18 (0.13) |
| 130 ≤ kW < 560 | 4.0 (3.0) | 0.12 (0.09) |
| kW ≥ 560 | 3.8 (2.8) | 0.12 (0.09) |
Engines of all sizes had to meet smoke standards of 20/15/50% opacity at acceleration/lug/peak modes, respectively.
The regulations included several other provisions, such as averaging, banking and trading of emission credits and maximum “family emission limits” (FEL) for emission averaging.
The origin of this article: https://www.dieselnet.com/standards/us/nonroad.php#tier3
